Comnet CNGE2FE8MSPOE Informazioni Techniche

INSTALLATION AND OPERATION MANUAL CNGE2FE8MSPOE ENVIRONMENTALLY HARDENED MANAGED ETHERNET SWITCH WITH (8) 10/100TX + (2) 10/100/

3 Sensitivity: -36 to -32 dBm (Single mode); -34 to -30 dBm (Multi mode) PoE pin assignment RJ45 port # 1~# 8 support IEEE 802.3af End-point, Alterna

93 6.20.3 SNMPV3 Configuration Configure the SNMP V3 function. Context Table Configure SNMP v3 context table. Assign the context name of context t

94 SNMP V3 configuration interface Access Table Configure SNMP v3 access table.  Context Prefix: set up the context name.  Group Name: set up

95 MIBview Table Configure MIB view table.  ViewName: set up the name.  Sub-Oid Tree: fill the Sub OID.  Type: select the type – exclude or in

96 6.21 QoS Configuration Quality of Service (QoS) is the ability to provide different priority to different applications, users or

97 QoS Configuration interface

98 6.21.2 Port-based Priority Configure the priority level for each port. With the drop-down selection item of Priority Type above being selected a

99 When the IP packet is received, the system will check the TOS level value in the IP packet that has received. For example, the user sets t

100 6.22 IGMP Configuration The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol (IP) suite.

101 IGMP Configuration interface

102 6.23 X-Ring X-Ring provides a faster redundant recovery than Spanning Tree topology. The action is similar to STP or RSTP, but the

4 61000-4-4, CE EN61000-4-5, CE EN61000-4-6, CE EN61000-4-8, CE EN61000-4-11, CE EN61000-4-12, CE EN61000-6-2, CE EN61000-6-4 Safety UL, cUL, CE/EN

103 Enable Couple Ring string label.  Couple Port: Assign the member port which is connected to the other ring group.  Control Port: When the

104 6.24 LLDP Configuration Link Layer Discovery Protocol (LLDP) is defined in the IEEE 802.1AB, it is an emerging standard which pr

105 6.25 Security—802.1X/Radius Configuration 802.1x is an IEEE authentication specification which prevents the client from accessing a wireless ac

106 802.1x System Configuration interface

107 6.25.2 Port Configuration You can configure the 802.1x authentication state for each port. The state provides Disable, Accept, Reject, and Autho

108 802.1x Per Port Setting interface

109 6.25.3 Misc Configuration  Quiet Period: Set the period which the port doesn’t try to acquire a supplicant.  TX Period: Set the period

110 6.26 MAC Address Table Use the MAC address table to ensure the port security. 6.26.1 Static MAC Address You can add a static MAC address that

111 Static MAC Addresses interface

112 6.26.2 MAC Filtering By filtering MAC address, the switch can easily filter the pre-configured MAC address and reduce the un-safety. You can add

5 1.2 Software Features Management SNMP v1 v2c, v3/ Web/Telnet/CLI SNMP MIB RFC 1215 Trap, RFC1213 MIBII, RFC 1157 SNMP MIB, RFC 1493 Bridge MIB, R

113 6.26.3 All MAC Addresses You can view all of the MAC addresses learned by the selected port.  Select the port number.  The selected port of

114 6.26.4 MAC Address Table—Multicast Filtering Multicasts are similar to broadcasts, they are sent to all end stations on a LAN or VLA

115 Multicast Filtering interface

116 6.27 Power over Ethernet This segment shows the Power over Ethernet function. PoE Status  Actual Power Consumption: This column shows the r

117 subtracted from the pre-capacitance voltage to get a charge rate. If this charge rate is within the window of the PD signatures, the device is co

118 6.28 Factory Default Reset switch to default configuration. Click to reset all configurations to the default value. Factory Default interf

119 6.29 Save Configuration Save all configurations that you have made in the system. To ensure the all configuration will be saved. Click to sa

120 6.30 System Reboot Reboot the switch in software reset. Click to reboot the system. System Reboot interface

121 Troubles shooting  Verify that is using the right power cord/adapter (DC 24-48V), please don’t use the power adapter with DC out

122 Appendix A—RJ45 Pin Assignment RJ45 Pin Assignments The UTP/STP ports will automatically sense for Fast Ethernet (10Base-T/100Base-TX

6 Port Mirror Supports 3 mirroring types: “RX, TX and Both packet”. IGMP Supports IGMP snooping v1,v2 256 multicast groups and IGMP query IP Security

123 3 Transmit Data plus (TD+) Receive Data plus (RD+) 6 Transmit Data minus (TD-) Receive Data minus (RD-)  10/100Base-TX Cable Schematic The fo

124  10/100/1000Base-TX Cable Schematic Straight through cables schematic

125 Cross over cables schematic

126 RJ45 Pin Assignment of PoE With 100BASE-TX/10BASE-T cable, pins 1 and 2 are used for transmitting data, and pins 3 and 6 for receiving data; pin

127  Pin out of PoE Endspan Hub/Switch Pin Signal / Name 1 TX+/VCC+ 2 TX-/VCC+ 3 TX+/VCC- 4 5 6 TX-/VCC- 7 8 Note ‘+’ and ‘-‘ signs represent

128 Appendix B—Command Sets Commands Set List User EXEC E Privileged EXEC P Global configuration G VLAN database

129 [Ip-address] [Subnet-mask] [Gateway] address of switch 192.168.1.1 255.255.255.0 192.168.1.254 ip dhcp G Enable DHCP client function of switch s

130 [Hours] (in hour) leasetime 1 dhcpserver ipbinding [IP address] I Set static IP for DHCP clients by port switch(config)#interface fastEthernet 2

131 telnet server Port Commands Set Netstar Commands Level Description Example interface fastEthernet [Portid] G Choose the port for modification

132 bandwidth type all I Set interface ingress limit frame type to “accept all frame” switch(config)#interface fastEthernet 2 switch(config-if)#bandw

7 SNMP Trap 1. Cold start 2. Link up/down 3. X-Ring topology changed 4. Authorization fail 5. PD disconnect trap-PoE port event DHCP Provides DHCP

133 and zero means no limit. show bandwidth I Show interfaces bandwidth control switch(config)#interface fastEthernet 2 switch(config-if)#show bandwi

134 Trunk Commands Set Netstar Commands Level Description Example aggregator priority [1~65535] G Set port group system priority switch(config)#aggre

135 comma(ex.2, 3, 6) show aggregator P Show the information of trunk group switch#show aggregator 1 or switch#show aggregator 2 or switch#show aggre

136 port [PortNumbers] show vlan [GroupID] or show vlan V Show VLAN information switch(vlan)#show vlan 23 no vlan group [GroupID] V Delete port base

137 [PortNumber] trunk-link tag [TaggedVID List] VLAN by trunk group trunk-link tag 2,3,6,99 or switch(vlan)#vlan 8021q trunk 3 trunk-link tag 3-20 v

138 protocol data unit (BPDU) message from the root switch within this interval, it recomputed the Spanning Tree Protocol (STP) topology. spanning-tr

139 command to set the path cost for Spanning Tree Protocol (STP) calculations. In the event of a loop, spanning tree considers the path cost when se

140 interface. switch(config-if)#stp-admin-non-stp False show spanning-tree E Displays a summary of the spanning-tree states. switch>show s

141 igmp enable G Enable IGMP snooping function switch(config)#igmp enable Igmp query auto G Set IGMP query to auto mode switch(config)#igmp query au

142 LLDP Commands Set Netstar Commands Level Description Example lldp enable G Enable LLDP function switch(config)#lldp enable lldp interval [Time se

8 1.3 Package Contents Please refer to the package content list below to verify them against the checklist.  8 10/100TX + 2 10/100/1000T/Mini

143 no mac-address-table G Remove dynamic entry of MAC address table switch(config)#no mac-address-table SNMP Commands Set Netstar Commands Level

144 [Group Name] password [Authentication Password] [Privacy Password] Privacy password could be empty. snmpv3 access context-name [Context Name ]

145 [User Name] user of SNMPv3 agent. Test no snmpv3 access context-name [Context Name ] group [Group Name ] security-level [NoAuthNoPriv|AuthN

146 port of monitor function monitor tx [Port ID] G Set TX destination port of monitor function switch(config)#monitor tx 3 show monitor P Show port

147 8021x system accountport [port ID] G Use the 802.1x system account port global configuration command to change the accounting port switch(config

148 8021x misc servertimeout [sec.] G Use the 802.1x misc server timeout global configuration command to set the server timeout. Switch(config)#8021

149 backup flash:backup_cfg G Save configuration to TFTP and need to specify the IP of TFTP server and the file name of image. Switch(config)#backup

150 [IP address] server IP 192.168.1.5 smtp sender [sendername] G Configure sender of mail switch(config)#smtp snder [email protected] smtp authentication

151 Down|Both] switch(config-if)#event smtp both show event P Show event selection switch#show event no event device-cold-start G Disable cold start

152 SNTP Commands Set Netstar Commands Level Description Example sntp enable G Enable SNTP function switch(config)#sntp enable sntp daylight G Enable

9 Chapter 2 Hardware Description In this paragraph, it will describe the Industrial switch’s hardware spec, port, cabling information,

153 number sntp sync-interval [Secs] G Set synchronization interval switch(config)#sntp sync-interval 64 show sntp P Show SNTP information switch#sho

154 no ring couplering G Disable couple ring switch(config)# no ring couplering no ring dualhoming G Disable dual homing switch(config)# no ring dual

155 ComNet Customer Service Customer Care is ComNet Technology’s global service center, where our professional staff are ready to answer your que

10 2.3 Top View The top panel of the 8 10/100TX w/ X-Ring Managed Industrial Switch has one terminal block connector of two DC power

11 2.4 LED Indicators The diagnostic LEDs that provide real-time information of system and optional status are located on the front

12 (Lower LED) Off 10/100M On The SFP port is linking Blinks The port is transmitting or receiving packets from the TX device. Link/Active (P9, P10

FCC Warning This Equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 15 of th

13 Chapter 3 Hardware Installation In this paragraph, we will describe how to install the 8 10/100TX w/ X-Ring Managed Industrial Swi

14 3.2 DIN-Rail Mounting The DIN-Rail is screwed on the industrial switch when out of factory. If the DIN-Rail is not screwed on the industrial swi

15

16 1. First, insert the top of DIN-Rail into the track. 2. Then, lightly push the DIN-Rail into the track. 3. Check if the DIN-Rail is tight

17 3.3 Wall Mount Plate Mounting Follow the steps below to mount the industrial switch with wall mount plate. 1. Remove the DIN-Rail from the

18 3.4 Wiring the Power Inputs Please follow the steps below to insert the power wire. 1. Insert DC power wires into the contacts 1 and 2 for po

19 3.5 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture show

20 3.6 Cabling  Use four twisted-pair, Category 5e or above cabling for RJ45 port connection. The cable between the switch and the li

21 To connect the transceiver and LC cable, please follow the steps shown below: First, insert the transceiver into the SFP module. Notice that th

22 LC connector to the transceiver

Content Chapter 1! Introduction ...1!1.1! Hardware Features ... 1!1.2! S

23 To remove the LC connector from the transceiver, please follow the steps shown below: First, press the upper side of the LC connector to release

24 Chapter 4 Network Application This chapter provides some sample applications to help user to have more actual idea of industrial switch f

25 The illustration below shows an example of power over Ethernet application.

26 4.1 X-Ring Application The industrial switch supports the X-Ring protocol that can help the network system to recovery from network

27 4.2 Coupling Ring Application In the network, it may have more than one X-Ring group. By using the coupling ring function, it can connect eac

28 4.3 Dual Homing Application Dual Homing function is to prevent the connection lose from between X-Ring group and upper level/core sw

29 Chapter 5 Console Management 5.1 Connecting to the Console Port The supplied cable which one end is RS-232 connector and the other

30 NC 7 Brown/White NC 8 Brown 5.3 Login in the Console Interface When the connection between Switch and PC is ready, turn on the PC a

31 Having finished the parameter settings, click ‘OK’. When the blank screen shows up, press Enter key to have the login prompt appears. Key

32 5.4 CLI Management The system supports the console management—CLI command. After you log in on to the system, you will see a command promp

5.2! Pin Assignment ... 29!5.3! Login in the Console Interface ... 30!5.4! CLI Management

33 EXEC mode. • Display advanced function status • Save configuration Global Configuration Enter the configure command while in privileged EXEC mode.

34 Chapter 6 Web-Based Management This section introduces the configuration and functions of the Web-Based management. 6.1 About Web-based Manage

35 6.3 System Login 1. Launch the Internet Explorer on the PC 2. Key in “http:// “+” the IP address of the switch”, and then Press “Enter”. 3.

36 6.4 System Information User can assign the system name, description, location and contact personnel to identify the switch. The vers

37 6.5 IP Configuration The switch is a network device which needs to be assigned an IP address for being identified on the netw

38 IP configuration interface

39 6.6 DHCP Server DHCP is the abbreviation of Dynamic Host Configuration Protocol that is a protocol for assigning dynamic IP addresses

40 6.6.1 System configuration  DHCP Server: Enable or Disable the DHCP Server function. Enable—the switch will be the DHCP server on your local ne

41 6.6.2 Client Entries When the DHCP server function is enabled, the system will collect the DHCP client information including the assigned IP addr

42 6.6.3 Port and IP Bindings Assign the dynamic IP address bound with the port to the connected client. The user is allowed to fil

6.11! IP Security...57!6.12! User Authentication... 59!6.13! Port St

43 6.7 TFTP It provides the functions allowing the user to update the switch firmware via the Trivial File Transfer Protocol (TFTP

44 6.7.2 Restore Configuration You can restore a previous backup configuration from the TFTP server to recover the settings. Before doi

45 6.7.3 Backup Configuration You can back up the current configuration from flash ROM to the TFTP server for the purpose of recove

46 6.8 System Event Log This page allows the user to decide whether to send the system event log, and select the mode which the system event log wi

47 Syslog Configuration interface

48 6.8.2 System Event Log—SMTP Configuration Simple Mail Transfer Protocol (SMTP) is the standard for email transmissions across the network. You

49 SMTP Configuration interface

50 6.8.3 System Event Log—Event Configuration Having ticked the Syslog/SMTP checkboxes, the event log/email alert will be sent to the system log ser

51 Event Configuration interface

52 6.9 Fault Relay Alarm The Fault Relay Alarm function provides the Power Failure and Port Link Down/Broken detection. With both power input 1 and

6.22! IGMP Configuration ... 100!6.23! X-Ring ... 102!6.24! LLDP Co

53 6.10 SNTP Configuration SNTP (Simple Network Time Protocol) is a simplified version of NTP which is an Internet protocol used to synchronize

54 EDT - Eastern Daylight!EST - Eastern Standard CDT - Central Daylight!-5 hours!7 am!CST - Central Standard MDT - Mountain Daylight!-6 hours!6 am!MS

55 ZP6 - USSR Zone 5!+6 hours!6 pm!WAST - West Australian Standard!+7 hours!7 pm!CCT - China Coast, USSR Zone 7!+8 hours!8 pm!JST - Japan Standard, U

56  Daylight Saving Offset (mins): For non-US and European countries, specify the amount of time for day light savings. Please key in the valid fig

57 6.11 IP Security IP security function allows the user to assign 10 specific IP addresses that have permission to manage the switch through

58 IP Security interface

59 6.12 User Authentication Change web management login user name and password for the management security issue.  User name: Type in

60 6.13 Port Statistics The following chart provides the current statistic information which displays the real-time packet transfer st

61 Port Statistics interface

62 6.14 Port Control In Port control you can configure the settings of each port to control the connection parameters, and the status

VLAN Commands Set ... 135!Spanning Tree Commands Set ... 137!QOS Commands Set...

63 Port Control interface

64 6.15 Port Trunk Port trunking is the combination of several ports or network cables to expand the connection speed beyond the l

65  Select the ports to join the trunk group. The system allows a maximum of four ports to be aggregated in a trunk group. Click and the por

66 6.15.2 Aggregator Information  LACP disabled Having set up the aggregator setting with LACP disabled, you will see the local stati

67 Static Trunking Group information  Group Key: This is a read-only column field that displays the trunk group ID.  Port Member: This is a

68  LACP enabled Having set up the aggregator setting with LACP enabled, you will see the trunking group information between two switches on the ta

69 Switch 1 configuration interface Aggregation Information of Switch 1 5. Click on the tab of Aggregator Information to check the trunked group

70  Switch 2 configuration Switch 2 configuration interface 1. Set System Priority of the trunk group. The default is 1. 2. Select a trunk gro

71 Aggregation Information of Switch 2 5. Click on the tab of Aggregator Information to check the trunked group information as the illustration sh

72 6.15.3 State Activity Having set up the LACP aggregator on the tab of Aggregator Setting, you can configure the state activity for the members of

1 Chapter 1 Introduction The 8 10/100TX + 2 10/100/1000T/Mini-GBIC Combo with 8 PoE Injectors Managed Industrial Switch is a cost-ef

73 State Activity of Switch 2

74 6.16 Port Mirroring The Port mirroring is a method for monitor traffic in switched networks. Traffic through ports can be monitored by one speci

75 6.17 Rate Limiting You can set up every port’s bandwidth rate and frame limitation type.  Ingress Limit Frame type: select the frame ty

76 is 10Mbps, users can set it’s effective egress rate is 1Mbps, ingress rate is 500Kbps. The switch performs the ingress rate by packet counter to m

77 6.18 VLAN configuration A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain, which would allow you

78 6.18.1 Port-based VLAN A port-based VLAN basically consists of its members—ports, which means the VLAN is created by grouping the selected ports.

79  Pull down the selection item and focus on Port Based then press to set the VLAN Operation Mode in Port Based mode.  Click to add a new

80  You will see the VLAN list displays. VLAN—Port Based Edit/Delete interface  Use to delete the VLAN.  Use to modify group name, VLA

81 6.18.2 802.1Q VLAN Virtual Local Area Network (VLAN) can be implemented on the switch to logically create different broadcast domain. When the

82 802.1Q Configuration  Pull down the selection item and focus on 802.1Q then press to set the VLAN Operation Mode in 802.1Q mode.  Enable G

2 Packet Buffer 1Mbits MAC Address 8K MAC address table Flash ROM 4Mbytes DRAM 32Mbytes Connector 10/100TX: 8 x RJ45 10/100/1000T/ Mini-GBIC Combo: 2

83  Trunk Link: A segment which provides the link path for one or more VLAN-aware devices (switches). A Trunk Port, connected to the trunk

84 802.1Q VLAN interface Group Configuration Edit the existing VLAN Group.  Select the VLAN group in the table list.  Click .

85 Group Configuration interface  You can modify the VLAN group name and VLAN ID. Group Configuration interface  Click .

86 6.19 Rapid Spanning Tree The Rapid Spanning Tree Protocol (RSTP) is an evolution of the Spanning Tree Protocol and provides for faster spanning

87 RSTP System Configuration interface

88 6.19.2 Port Configuration This web page provides the port configuration interface for RSTP. You can assign higher or lower priority to each port.

89 RSTP Port Configuration interface

90 6.20 SNMP Configuration Simple Network Management Protocol (SNMP) is the protocol developed to manage nodes (servers, workstations, routers, swi

91 SNMP System Configuration interface

92 6.20.2 Trap Configuration A trap manager is a management station that receives the trap messages generated by the switch. If no trap manager